SmallRig Full Camera Cage for Sony Alpha 7R V/Alpha 7 IV / A7R IV/Alpha 7 S III/Alpha 1-3667B
Improved Design: 1. A cold shoe is added to the upper right corner of the cage to facilitate the installation of accessories such as Microphone 3468 and LED Video light 3286; 2. Two 1/4"-20 threaded holes with a spacing of 18mm are added at the bottom, which is compatible with SmallRig Quick Release Plate for Arca 3154. A QD hole is added at the bottom, which is compatible with QD quick release shoulder straps and other accessories. | For Sony A7R V/A7 IV/A7S III/A1/A7R IV: SmallRig Cage 3667 is designed for Sony A7R V, A7 IV, A7S III, A1, A7R IV to facilitate low-angle shots and protect the camera while offering a wide range of accessory mounts. NOTE: The HDMI Cable Clamp 3000 is not compatible with Alpha 1 and Alpha 7R IV because it will block the synchro terminal interface when used on the Alpha 7R V. | Multiple Mounting Points: The cage has multiple 1/4"-20 holes and 3/8"-16 positioning holes for ARRI, which can attach accessories such as the upper handle 3765, the side handle 2093, and the monitor stand 2903B. There are 2 built-in cold shoe interfaces, which can install microphones, fill lights and other equipment; the QD hole at the bottom is compatible with QD shoulder straps. Holes are reserved on both sides and bottom of the cage to attach Wrist Strap PAC2456 and Shoulder Strap PSC2428. | Three-Point Locking: A positioning pin is added at the bottom of the cage, and the 1/4"-20 screw and the left M2.5 screw form a three-point locking to make the camera stable. Adjust the direction of the left locking slider to adapt to different models, [A7 IV] side is suitable for Alpha 7 IV and Alpha 7R V, [A7S III/A1] side is suitable for Alpha 7S III / Alpha 1 / Alpha 7R IV | All-Round Protection: Built-in all-round rubber gasket to prevent scratches. With the cage installed, the camera interface, dials, buttons and changing batteries are not affected. The opening and closing wrench design is added to the position of the battery compartment, which fits the curve of the fuselage more, solves the problem of placing the little finger, and enhances the grip of the fuselage. | Built-in Quick Release Plate: The bottom quick release plate for Arca has added 1/4"-20 holes with a spacing of 18mm, which is compatible for DJI RS 2 / RSC 2 / RS 3 / RS 3 Pro, and can also be adapted to DJI RS 2 / RSC 2 stabilizer mounting board (riser plate) and SmallRig Quick Release Plate for Arca 3154. | Power Backup Solution: SmallRig NP-FZ100 camera battery charger set is available now, two 2040mAh(Real) rechargeable batteries and a charger brings long battery life for your videos and photos shooting, if you need a sufficient power supply, please search SmallRig NP-FZ100 Battery 3824
All major credit & debit cards accepted securely:
Imported from USA to INDIA 
Use 220V to 110V Adapter for Electronic appliances
(Upgraded Version) SMALLRIG Full Cage for Sony Alpha 7R V / Alpha 7 IV / Alpha 7S III / Alpha 1 / Alpha 7R IV - 3667B
Key Features:
1. One-piece full cage protects camera
2. A hinged arm at the battery door fits camera curve and enhances grip experience
3. Multiple mounting points: 1/4"-20 threaded holes, 3/8" -16 locating holes for ARRI, cold shoe mounts, NATO rail and QD socket support handles, microphones, LED lights, monitors, etc.
4. Triple-point locking: fixes camera via one bottom locating pin, one 1/4"-20 screw and the one M2.5 screw on the left side
5. Quick release plate for Arca-Swiss on the bottom for quick switching between tripod, stabilizer (for DJI RS 2 / RSC 2 / RS 3 / RS 3 Pro) and handheld shooting
SmallRig Full Cage for Sony Alpha 7R V / Alpha 7 IV / Alpha 7S III / Alpha 1 / Alpha 7R IV 3667B is designed to provide accessory mounts and protect camera. It locks camera via one bottom locating pin, one 1/4"-20 screw and the one M2.5 screw on the left side. The side lock adapters need to be adjusted the installation direction for fitting different camera types, printed with“A7 IV”is for Alpha 7 IV and Alpha 7R V while printed with “A7S III/A1”is for Alpha 7S III / Alpha 1 / Alpha 7R IV. Built-in all-round protective spacers prevent the camera from being scratched. The cage gives access to interfaces, dials, buttons or battery door. There is a spindle spanner at the battery compartment which fits camera curve and leave room for little finger for comfortable grip. 1/4"-20 threaded holes, 3/8" -16 locating holes for ARRI and cold shoe mounts support top handle 2165C, side handle 2093, monitor mount 2903, microphones, LED lights, monitors, etc. Bottom QD socket support QD shoulder strap. quick release plate for Arca-Swiss at the bottom is compatible for DJI RS 2 / RSC 2 / RS 3 / RS 3 Pro, the quick release plate (riser plate) for DJI RS 2/RSC 2 stabilizer for stabilizer shooting, and quick release plate for Arca-Swiss 3154. Optional Cable Clamp for HDMI 3000 works with Alpha 7R V / Alpha 7 IV / Alpha 7S III to protect interfaces and ensure stable signal transmission during filming. Holes on the sides and bottom of the cage allow attaching such accessories as hand strap PAC2456 and shoulder strap PSC2428. Besides, the cage comes with a built-in magnetic spanner that facilitate disassembly and assembly.
Notes:
After fixing the 1/4"-20 screw at the bottom of the cage, remove the anti-deflection pin from the staging hole in the battery compartment position and secure it to the corresponding position.
To use the side lock adapter, please remove the split ring on the left side of the camera first.
Cable Clamp for HDMI 3000 is not compatible with Alpha 1 and Alpha 7R IV cameras and will interfere with the synchro terminal interface when used on Alpha 7R V camera.
Compatibility:
For Sony Alpha 7R V
For Sony Alpha 7 IV
For Sony Alpha 7S III
For Sony Alpha 1
For Sony Alpha 7R IV
In the Box:
1 x Cage
Product Dimensions: 146 x 107.6 x 64.5mm
Package Dimensions: 165 x 155 x 85mm
Product Weight: 180g±5g
Package Weight: 286g±5g
Material(s): Aluminum Alloy, Stainless Steel, Silicone
RELATED PRODUCTS: 3668B, 3669B, 3660, 3666, 3000, 2165C, 2093, 2903B, PAC2456
