ID: 3/8inch (10mm);OD: 2/3inch(17mm).Material: NBR. | Working Pressure: 300psi.Burst Pressure: 1160psi.Temperature Range: -40°F to 257°F.Minimum Bend Radius: 3.9inch(100mm). | Applicable Medium: 3/8 id fuel line can work with diesel/biodiesel/gasoline/oil/grease/water and air,etc. | Application: SAE 30R7 rubber fuel line widely used in fuel system,oil cooling, steam emission,please check the pressure of application before perchase. | EVIL ENERGY provide 5ft 3/8inch fuel hose 3-month warranty.Any problem you might have,please feel free to contact us via Amazon message.

Joins 4.0" OD pipe to 4.0" OD pipe, besides, we offer you 4 different sizes and you would better measure before pruchase. These clamps feature unitized construction which minimized part number complexity and maximizes material efficiency for reduced weight. | Butt joint band clamps is a simple, effective way to connect exhaust system components such as pipes, mufflers and catalytic converters. Unique seal and high clamp loads are provided without distorting your exhaust components, allowing the flexibility to disassemble for service. | Distributes the clamping force evenly over the entire 360° to prevent leaks and control material distortion. Easy and less time consuming to install or remove with one bolt. Features T-304 band stainless steel and aluminized steel hardware. | The band clamp is a wide strap of metal, typically stainless, which wraps around the exhaust pipe joint. Our product is a pre-formed ring, also, it is now more commonly used in higher-end aftermarket exhaust systems using slip-fit, because they are relatively cheap, and are reusable without damaging the pipes. | EVIL ENERGY provide this product have 3-month warranty.We value your shopping experience and strive to offer a high-quality product and service.

[Size] 4AN to 1/4 inch barb, and thread size of 4an is 7/16-20 UNF. | [Application] The barb fitting only work with rubber fuel line. | [Parameter] Max working pressure: 1500PSI; Temperature range: -40℉ to 248℉. | [Material] Made of aluminum alloy 6061-T6. | [Installation] Easy to install, it is recommended to use clamps to enhance sealing.

[Size] The thread size of 4AN is 7/16-20UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -40℉ to 248℉ (-40℃ to 120℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 4AN is 7/16-20 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -40℉ to 248℉ (-40℃ to 120℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

Size: AN4 to 1/4" NPT, the thread size of 4AN is 7/16-20 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN4 to 1/8" NPT, the thread size of 4AN is 7/16-20 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: 4AN flare to 1/4" NPT, the thread size of 4AN is 7/16-20 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: 4AN flare to 3/8" NPT, the thread size of 4AN is 7/16-20 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

ID: 5/16inch (8mm),OD: 9/16inch(14mm).Material: NBR. | Working Pressure: 300psi. Burst Pressure: 1160psi. Temperature Range: -40°F to 257°F. Minimum Bend Radius: 3.14inch(80mm). | Applicable Medium: 5/16 id fuel line can work with diesel/biodiesel/gasoline/Oil/grease/water and air,etc. | Application: SAE 30R7 rubber fuel line widely used in fuel system, oil cooling, steam emission, please check the pressure of application before perchase. | EVIL ENERGY provide 5ft 5/16inch fuel hose 3-month warranty.Any problem you might have, please feel free to contact us via Amazon message

ID: 5/16inch (8mm);OD: 9/16inch(14mm).Material: NBR. | Working Pressure: 300psi.Burst Pressure: 1160psi.Temperature Range: -40°F to 257°F.Minimum Bend Radius: 3.14inch(80mm). | Applicable Medium: 5/16 id fuel line can work with diesel/biodiesel/gasoline/oil/grease/water and air,etc. | Application: SAE 30R7 rubber fuel line widely used in fuel system,oil cooling,steam emission,please check the pressure of application before perchase. | EVIL ENERGY provide 25ft 5/16inch fuel hose 3-month warranty.Any problem you might have,please feel free to contact us via Amazon message

The female AN6 180 degree swivel fittings are made of lightweight aluminum alloy 6061-T6 material for strong strength and good durability. Black anodized for great appearance and anti-corrosion, superior thread strength. Max Working Pressure: 1000psi. Working Temperature Range: -65℉ to 252℉ （-53℃ to 122℃). Can be suitable for competition applications where reduced weight is needed. | 6AN 180 degree swivel hose end is widely used in oil/ fuel/ water/ fluid/ airline etc. Connect oil gas line, braided fuel line ,clutch hose,turbo line etc. Our swivel fitting is work with nylon braided fuel hose . They are not compatible with PTFE hose, E85, rubber hose . | These new full flow swivel hose ends swivel 360° to allow for a quick alignment of the hose after assembly.Swivel hose end can be reused and recycle if you do not want them to stay in the original place. | Weld-free construction that gives better fluid flow and integrity over the normal brazed together hose ends. Swivel fittings are easy to use and don't require special equipment. We normally recommend a bit of assembly lube to help prevent any galling. | EVIL ENERGY provide this product have 3-month warranty.We value your shopping experience and strive to offer a high-quality product and service.

[Size] 6AN to 3/8 inch barb, and thread size of 6an is 9/16-18UNF. | [Application] The barb fitting only work with rubber fuel line. | [Parameter] Max working pressure: 1500PSI; Temperature range: -40℉ to 248℉. | [Material] Made of aluminum alloy 6061-T6. | [Installation] Easy to install, it is recommended to use clamps to enhance sealing.

Fuel hardline fitting: Only compatible with hard tube. | Size: 6AN to 3/8 inch,the thread size of the 6AN is 9/16UNF.It's fits to 3/8" OD hardline,please measure before perchase. | Material: Made of aluminium alloy fitting and brass ferrule. | Application: This 3/8 hardline to 6an fitting is widely used in Brake System / Air & Fuel Delivery/ Engine Modification / Oiling System / Cooling System. | Maximum working pressure: 4000PSI,Working temperature: -65°F to 252°F.

[Size] The thread size of 6AN is 9/16-18 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -65℉ to 252℉ (-53℃ to 122℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 6AN is 9/16-18 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -65℉ to 252℉ (-53℃ to 122℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 6AN is 9/16-18 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -65℉ to 252℉ (-53℃ to 122℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 6AN is 9/16-18 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose. | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -40℉ to 248℉ (-40℃ to 120℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 6AN is 9/16-18 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -65℉ to 252℉ (-53℃ to 122℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 6AN is 9/16-18 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -40℉ to 248℉ (-40℃ to 120℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

Size: AN6 to 1/2" NPT, the thread size of 6AN is 9/16-18 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered threads. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN6 to 1/2" NPT, the thread size of 6AN is 9/16-18 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN6 to 1/4" NPT, the thread size of 6AN is 9/16-18 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN6 to 1/4" NPT, the thread size of 6AN is 9/16-18 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing: The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended.

Size: AN6 to 1/8" NPT, the thread size of 6AN is 9/16-18 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN6 to 3/8" NPT, the thread size of 6AN is 9/16-18 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing: The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended.

Please Attention that the 6AN PTFE hose end can be work with PTFE fuel line ONLY. | Thread Size of 6AN PTFE Fitting is 9/16-18UNF and work with PTFE fuel line(Hose ID: 0.31 inch OD: 0.43-0.47 inch). | The PTFE hose end is reusable, just replace a new ferrule if you reinstall the fitting. | EVIL ENERGY Provide plently kind of fuel fittings, Swivel, push-on lock, PTFE hose end and other fitting adapters. | Warrany: EVIL ENERGY provide PTFE hose end 6-month warranty. We value your shopping experience and strive to offer a high-quality product and service.

The female AN6 swivel fittings are made of lightweight aluminum alloy 6061-T6 material for strong strength and good durability. Black anodized for great appearance and anti-corrosion, superior thread strength. Max Working Pressure: 1000psi. Working Temperature Range: -65℉ to 252℉ （-53℃ to 122℃). Can be suitable for competition applications where reduced weight is needed. | 6AN swivel hose end is widely used in oil/ fuel/ water/ fluid/ airline etc. Connect oil gas line, braided fuel line ,clutch hose,turbo line etc. Our swivel fitting is work with nylon braided fuel hose . They are not compatible with PTFE hose, E85, rubber hose . | These new full flow swivel hose ends swivel 360° to allow for a quick alignment of the hose after assembly.Swivel hose end can be reused and recycle if you do not want them to stay in the original place. | Weld-free construction that gives better fluid flow and integrity over the normal brazed together hose ends. Swivel fittings are easy to use and don't require special equipment. We normally recommend a bit of assembly lube to help prevent any galling. | EVIL ENERGY provide this product have 3-month warranty.We value your shopping experience and strive to offer a high-quality product and service.

Size: 6AN flare to 1/2" NPT, the thread size of 6AN is 9/16-18 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: 6AN flare to 1/4" NPT, the thread size of 6AN is 9/16-18 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: 6AN flare to 3/8" NPT, the thread size of 6AN is 9/16-18 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

The female AN8 45 Degree swivel fittings are made of lightweight aluminum alloy 6061-T6 material for strong strength and good durability. Black anodized for great appearance and anti-corrosion, superior thread strength. Max Working Pressure: 1000psi. Working Temperature Range: -65℉ to 252℉ （-53℃ to 122℃). Can be suitable for competition applications where reduced weight is needed. | 8AN 45 degree swivel hose end is widely used in oil/ fuel/ water/ fluid/ airline etc. Connect oil gas line, braided fuel line ,clutch hose,turbo line etc. Our swivel fitting is work with nylon braided fuel hose . They are not compatible with PTFE hose, E85, rubber hose . | These new full flow swivel hose ends swivel 360° to allow for a quick alignment of the hose after assembly.Swivel hose end can be reused and recycle if you do not want them to stay in the original place. | Weld-free construction that gives better fluid flow and integrity over the normal brazed together hose ends. Swivel fittings are easy to use and don't require special equipment. We normally recommend a bit of assembly lube to help prevent any galling. | EVIL ENERGY provide this product have 3-month warranty.We value your shopping experience and strive to offer a high-quality product and service.

APPLICATION- EVIL ENERGY push lock fitting is widely used in Oil/ Water/ Fluid/ Airline etc. Connect engine with air filter, the engine with radiator system, automobile air conditioning system, oil cooler etc. Our Push Lock fitting is only work with Rubber Push-Lock oil hose. They are not compatible with PTFE Hose, Nylon Braided Hose, or Stainless Steel Braided Hose. | Multi Sizes Supplied: Available in 3 sizes and three angles: 6AN, 8AN, 10AN/ straight, 45 degree, 90 degree.(PUSH LOCK FITTING NO INSTALLATION INSTRUCTIONS, detailed Installation steps look described in detail.) | Designed For Smooth Flow, the hose end fittings are made of high-quality aluminum alloy material for strong strength. Polished and anodized surface provide the bright appearance and corrosion protection. | ENVIRONMENTAL FRIENDLY- push lock fitting can be reused and recycle if you do not want them to stay in the original place. Due to the high-quality material which makes push lock fitting worked last for long. | Weld-free construction that gives better fluid flow and integrity over the normal brazed together hose ends. Push Lock fittings are easy to use and don't require special equipment. We normally recommend a bit of assembly lube to make it easier.

[Size] 8AN to 1/2 inch barb, and thread size of 8an is 3/4-16UNF. | [Application] The barb fitting only work with rubber fuel line. | [Parameter] Max working pressure: 1500PSI; Temperature range: -40℉ to 248℉. | [Material] Made of aluminum alloy 6061-T6. | [Installation] Easy to install, it is recommended to use clamps to enhance sealing.

The female AN8 90 Degree swivel fittings are made of lightweight aluminum alloy 6061-T6 material for strong strength and good durability. Black anodized for great appearance and anti-corrosion, superior thread strength. Max Working Pressure: 1000psi. Working Temperature Range: -65℉ to 252℉ （-53℃ to 122℃). Can be suitable for competition applications where reduced weight is needed. | 8AN 90 degree swivel hose end is widely used in oil/ fuel/ water/ fluid/ airline etc. Connect oil gas line, braided fuel line ,clutch hose,turbo line etc. Our swivel fitting is work with nylon braided fuel hose . They are not compatible with PTFE hose, E85, rubber hose . | These new full flow swivel hose ends swivel 360° to allow for a quick alignment of the hose after assembly.Swivel hose end can be reused and recycle if you do not want them to stay in the original place. | Weld-free construction that gives better fluid flow and integrity over the normal brazed together hose ends. Swivel fittings are easy to use and don't require special equipment. We normally recommend a bit of assembly lube to help prevent any galling. | EVIL ENERGY provide this product have 3-month warranty.We value your shopping experience and strive to offer a high-quality product and service.

[Size] The thread size of 8AN is 3/4-16UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -40℉ to 248℉ (-40℃ to 120℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 8AN is 3/4-16 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -65℉ to 252℉ (-53℃ to 122℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 8AN is 3/4-16 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -65℉ to 252℉ (-53℃ to 122℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 8AN is 3/4-16UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose. | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -40℉ to 248℉ (-40℃ to 120℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

Size: AN8 to 1/2" NPT, the thread size of 8AN is 3/4-16 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.